XJTAG logo
Open search box button Shopping cart button

Why Your Prototype Board Won’t Boot, and How to Fix It Faster.

Image of CEO of XJTAG Simon Payne Simon Payne, CEO, XJTAG |  Subscribe to LinkedIn newsletter

It’s the moment every engineer dreads: your new prototype arrives, you do some basic checks, power it on, and… nothing. No LEDs, no serial output, just silence. What went wrong? Is it a solder bridge, a missing pull-up, or a short hiding under a BGA? The clock’s ticking, and every hour lost brings you closer to a delayed project.

The Challenge

During bring-up, every second counts. You need to verify connections, check power rails, and confirm that devices are communicating properly,  all before you can even begin functional testing. But traditional debugging methods, oscilloscopes, logic probes, and manual checks, only get you so far, especially on dense, multi-layer boards.

The Common Pitfalls

Many teams rely on trial-and-error to find faults, reflowing, resoldering, and swapping components in hope of a breakthrough. Others jump straight into firmware debugging before confirming hardware integrity. The result? Days or even weeks wasted chasing invisible faults that could have revealed in minutes.

The Smarter Approach

When traditional debugging hits a wall, there’s a better way to bring up and test your prototype boards. Instead of spending hours with probes and trial‑and‑error fixes, engineers can now use advanced testing tools to access hidden pins, automate testing, and pinpoint faults faster.

Achieve Superior Test Coverage

This technology allows engineers to achieve high test coverage by using device pins as virtual test points, no need for complex fixtures or physical access to hard‑to‑reach BGAs.

A built‑in library of tens of thousands of components covers connection and functionality tests, letting teams efficiently test a wide range of devices and quickly resolve manufacturing faults.

Test Complex, Integrated Boards

An integrated development environment (IDE) guides engineers through creating and executing PCB tests to find assembly faults and validate the function of components, from LEDs to DDR5 memory.

The intuitive interface makes component categorisation quick, with ready‑made device models or easy scripting options using the test language. Tests can be run on any board, no programming or boot code needed, to locate faults before power‑up.

Find the Root of Problems, Quickly

Advanced diagnostics provide full visibility of the board’s state. Engineers can instantly see the fault type, nets and pins involved, and their exact location on schematics, pinpointing shorts in seconds.

Without any custom tests, interconnection testing finds opens, shorts, missing pull‑ups/downs, and faults hidden through logic or resistors. When an issue is found, additional tests run automatically to provide more context.

Take Full Control of Your Testing

All this capability is accessible without coding. The tools are designed for ease of use, featuring an extensive library of ready‑to‑use device models that simplify setup and reduce onboarding time.

Tests can also be customised to interact with boards in real time, bringing up power rails in sequence or adapting tests dynamically based on hardware configuration.

The Turning Point

Teams using XJTAG’s bring-up approach have cut prototype debug time from days to hours. Instead of endless probing, they validate entire interconnects instantly and move straight to firmware testing with confidence. The result? Faster validation, fewer surprises, and more predictable schedules.

The Takeaway

Prototype bring-up doesn’t have to be stressful. With the right method, you can find faults faster, protect your design from costly damage, and get to that satisfying first boot in record time.

Explore It Now

Check out the test-coverage-report. It’s completely free, just upload your design data to instantly visualise test coverage, identify untested devices, and strengthen your validation plan.

Tip: Before you start, use the Device Checker to see if your device is supported for testing.

The Device Checker currently checks for:

  • JTAG devices, with a BSDL file
  • “Test” devices, covered by a file in the XJEase Library
  • “Logic” devices, covered by a definition in the Logic Library

For Test and Logic devices, XJTAG can further test the board for connectivity using the expected behaviour of the device.

Check out our page on Testing Non‑JTAG Devices

Related Reading

complex development board with memories

Find the fault. Save the board.

Start free trial
“It’s Only a Small Board Change…” What Could Possibly Go Wrong? We recently spoke to an engineer about a new revision of an existing PCB. The message was: “It’s only an iterative change.” The implication was understandable: the design changes are small, so the additional test work should also be small. And they may be absolutely right. But it raises an important question: How do you know? A small PCB revision does not automatically mean a small test impact. How Much Test Work Does a Small PCB Revision Really Create? The answer depends less on how many things changed and more on what those changes affect. A reset signal may have moved. A buffer may have been added. A memory device may have been replaced. A previously unused FPGA pin may now be connected. A power rail or enable sequence may have changed. Each change may be small on the schematic, but if an existing test depends on it, the impact can be much greater. Every test makes assumptions about the hardware: which devices are fitted, how signals are connected, what can be controlled and observed, and how devices behave during test. Change one of those assumptions and the existing test may need to change too. What If the Change Is at the Centre of the Board? Now consider replacing the FPGA or processor at the heart of the design. Perhaps the new device performs essentially the same function and most of the surrounding circuitry is unchanged. It may look like a straightforward substitution. But that device may interact with a significant proportion of the board and therefore affect many existing tests. For teams using Boundary Scan, there is another important consideration: Is the BSDL file correct for the exact device and package now fitted? Boundary Scan software relies on the BSDL file to describe the device's pins, Boundary Scan cells, instructions and test capability. So a change that appears on the design change list as: “FPGA changed from A to B” could potentially affect considerably more of the existing test strategy than the change list initially suggests. This is why test effort isn't proportional to the number of changes. It depends on how central those changes are to the tests already developed. Regression Testing Isn't Just for Software Software engineers are familiar with regression testing. A small code change doesn't mean rewriting the entire application, but it does mean understanding what else could have been affected. PCB test deserves the same approach. For every revision, ask: What changed? Which existing tests depend on it? Which assumptions are still valid? Which tests can remain unchanged? Which tests need modifying? Is any additional test coverage required? The objective isn't to assume everything has changed. It's to avoid assuming nothing has. Reuse Should Still Be the Goal Last week, we looked at the value of reusing tests developed during bring-up through production, repair and support. A new board revision shouldn't change that principle. Good reusable tests should make iterative development easier. The aim is to preserve everything that remains valid and concentrate engineering effort only on the tests affected by the new design. Reuse the test — but validate the assumptions behind it. That is far more efficient than designing a complete test strategy again for every PCB revision. Closing Thought “It’s only an iterative change” may be completely true. And the additional test-development work may genuinely be trivial. But that should be the conclusion of an impact review, not the assumption at the start of one. When the next PCB revision is released, ask: What changed? Which of our existing tests depend on those changes? Are the assumptions behind those tests still valid? Then preserve everything that still works. The objective isn't to design a complete test from scratch. It's to know which tests need changing — and why. Board Design Tip of the Week When documenting your next PCB revision, add one more item to the change list: Test impact. For each design change, consider whether it affects: Component functionality or pinout Signal routing or connectivity Resets, enables or mode settings Power rails or sequencing Interfaces and control signals Physical test access Programming or configuration Existing test assumptions And if Boundary Scan forms part of your test strategy, also check whether the change affects the BSDL/device model or JTAG architecture. A short review at this stage can prevent a “small change” from becoming an unexpected test-development problem when the revised boards arrive. Discover more about your board design with the Free XJTAG Layout Viewer. To get started find out how the Free XJTAG Layout Viewer can help you see on your board: Download your Free XJTAG Layout Viewer today
Don’t Throw Away the Tests That Got Your Prototype Working The first prototype arrives and the engineering team begins the process of proving the hardware. Connections are checked. Memories are exercised. Peripherals are tested. Problems are found, understood and fixed. Eventually, the board works. And then something slightly strange can happen. Much of the test capability that helped get it working is never used again. Bring-Up Creates More Than a Working Board During bring-up, engineers build up a significant amount of knowledge about the hardware. They learn how to initialise devices. They discover which signals need to be controlled. They find ways of checking memories and peripherals. They work out how to distinguish between a software problem and a hardware problem. Sometimes this knowledge becomes a formal test. Sometimes it is a small utility written by one engineer. Sometimes it is little more than a sequence of commands, measurements or notes that helped prove a particular part of the board. But whatever form it takes, it has value. The question is: What happens to it once the prototype works? A Test Shouldn't Necessarily Be Used Only Once Some bring-up tests are naturally temporary. But many aren't. If a test helped prove that an interface was correctly connected on the first prototype, there may be no reason why the same test cannot help verify that interface again later. The purpose simply changes. During bring-up, the question might be: “Did we design this correctly?” During production: “Has this particular board been assembled correctly?” During repair: “Which part of this board is no longer behaving correctly?” Different stages of the product lifecycle. But often the same underlying hardware evidence is useful. Turn Engineering Knowledge into Something Repeatable There is an important difference between knowing how to test something and having a test that someone else can run. If an engineer manually performs a sequence of checks during bring-up, that knowledge may disappear when the project moves on. If the same procedure is documented and automated where practical, it becomes reusable. That means the effort invested during development can continue providing value. Instead of every new team starting again, the product carries some of its diagnostic knowledge with it. Boundary Scan Is Particularly Well Suited to Reuse Boundary Scan can be especially useful here because structural tests are based on the hardware and its connectivity rather than depending entirely on the final application software. A test created to verify connections between devices during bring-up can potentially verify those same connections during manufacturing. A test used to exercise a memory, peripheral or other accessible device may remain useful during fault diagnosis. The reason for running the test changes. The physical hardware being checked does not. That gives structural tests the potential to move with the product from development into production and later support. Don't Lose the Tests at Handover When a product moves from development into manufacturing, the handover typically includes things such as: Schematics PCB data BOMs Manufacturing information Firmware Programming files Test specifications It is worth asking whether the diagnostic capability developed during bring-up should be treated in exactly the same way. Which tests proved particularly useful? Which interfaces can be independently verified? Which procedures helped isolate previous faults? Which tools or scripts should be retained? If that knowledge stays with one engineer rather than moving with the product, its value can easily be lost. One Investment, Several Uses The same test capability can potentially support: Prototype bring-up — establishing confidence in the first hardware. Design verification — proving that important areas of the PCB behave as intended. Production — checking whether individual assemblies have been manufactured correctly. Repair and rework — confirming whether a fault has been successfully corrected. Failure analysis — narrowing down where to investigate a returned board. Long-term support — providing engineers with diagnostic capability years after the original development team has moved on. That starts to change the way we think about the cost of developing a test. It isn't necessarily an investment for one stage of the project. It can be an investment in the product's entire lifecycle. Where XJTAG Fits This is one reason an XJTAG project can become more than something used to bring up the first prototype. Once the design information, device models and tests have been developed, that work can potentially be reused as the product moves into manufacturing, repair and support. Rather than rebuilding the test strategy at every stage, the same underlying project can evolve with the hardware. The value isn't simply in running another test. It is in preserving and reusing what the engineering team has already learned. Closing Thought Getting the first prototype working shouldn't necessarily be the point at which your test investment ends. It can be the point at which that investment starts becoming reusable. The tests that help an engineer understand board number one may also help manufacturing verify board number 1,000—or help a service engineer understand a failure years later. A good test isn't just something you run. It's engineering knowledge you can reuse. Board Design Tip of the Week When your next prototype reaches the point where everyone agrees it is working, don't immediately move on. Ask: “Which of the tests and diagnostic procedures we've developed should follow this product into production and support?” Capture them. Document them. Automate them where practical. And consider keeping them under the same configuration control as the rest of the product. The knowledge required to prove the first board works may be just as valuable when a board much later in the product's lifecycle doesn't. Discover more about your board design with the Free XJTAG Layout Viewer. To get started find out how the Free XJTAG Layout Viewer can help you see on your board: Download your Free XJTAG Layout Viewer today
Your Board Already Has a Powerful PCB Test Capability The design has been verified, production starts, the first boards come through test successfully. Then one fails. That is the moment you discover how good your test strategy really is. Finding a fault on a prototype is one thing. The development team knows the design intimately, has access to schematics, debug software and bench equipment, and may be prepared to spend hours investigating an unusual problem. Production is different. When a manufactured board fails, the question isn't simply: “Does it work?” It becomes: “What's wrong with this particular board, and how quickly can we find the fault?” Prototype Debugging and Production Diagnosis Are Different During development, engineers are often investigating the design itself. Is the interface configured correctly? Does the circuit behave as expected? Are the component values right? Does the software initialise the hardware correctly? By the time a product reaches production, the design should already have been proven. The production test is answering a different question: Has this particular assembly been manufactured correctly? That changes the nature of the investigation. A Failure Needs to Narrow the Search Imagine a board fails because an interface is not responding. A basic production test may tell you exactly that: Interface failed. But the engineer still has to work out why. Is there an open connection? A short? A missing component? A badly soldered pin beneath a BGA? An incorrectly fitted device? Or is the problem somewhere else entirely? A useful test strategy should progressively reduce that search area. The closer the test can get from: “Something is wrong.” to: “Start looking here.” the more useful it becomes. This Is Where Structural Information Helps Functional testing is extremely valuable in production because it proves that the completed product behaves as expected. But when a functional test fails, the symptom can sometimes cover a large area of hardware. Structural testing provides a different layer of evidence. Boundary Scan can often verify inaccessible PCB connections independently of the application software and relate unexpected results back to the nets and devices involved. That can help answer an important question: Is this an assembly problem, and if so, where should we investigate first? Boundary Scan does not replace functional production testing. It complements it by providing another way to understand the hardware beneath the symptom. One Failed Board May Be Manageable If one board fails, spending an hour investigating it may not seem significant. But what happens when ten fail? Or fifty? Or when the same type of fault appears repeatedly? At that point, diagnostic time starts affecting manufacturing throughput. That is why the economics of production test aren't determined only by how quickly passing boards can be tested. They are also influenced by how efficiently failed boards can be diagnosed. A fast PASS/FAIL test followed by hours of fault finding may not be as efficient as it first appears. Don't Wait for the First Failure to Think About Diagnosis There is an important Design for Test lesson here. When the first failed production board arrives, the PCB design is already complete. If a reset cannot be controlled, an enable is inaccessible or an important interface cannot be exercised independently, the test engineer has to work within those constraints. The opportunity to make a simple schematic change may have disappeared months earlier. This is why testability shouldn't only ask: “Can we detect a failure?” It should also ask: “If it fails, what information will we have?” That question is much easier to answer while the schematic is still open. Carry What You Learned During Bring-Up into Production There is another opportunity that is often overlooked. Structural tests developed during prototype bring-up don't necessarily need to be discarded once the design is working. Tests that proved connectivity, memories, peripherals or interfaces during development may also provide useful coverage in production. That means the effort invested in understanding the first prototypes can potentially become part of the manufacturing test strategy. Instead of starting again, knowledge moves forward with the product. Closing Thought A string of passing boards doesn't really test your diagnostic strategy. The first failure does. That is when you discover whether your test simply detects a problem or actually helps the engineer understand it. And the difference between knowing: “This board failed.” and: “This is where you should start looking.” can determine whether the problem is diagnosed in minutes, investigated for hours or placed on a growing bone pile marked: Investigate later. The best production tests don't just catch faults. They help engineers understand them. Board Design Tip of the Week Before releasing your next design, choose three realistic manufacturing faults. For example: An open connection beneath a BGA A short between two adjacent signals An incorrectly fitted peripheral Then ask: “If this happened on the production line, what would our test actually tell us?” If the answer is simply: FAIL there may still be work to do. Discover more about your board design with the Free XJTAG Layout Viewer. To get started find out how the Free XJTAG Layout Viewer can help you see on your board: Download your Free XJTAG Layout Viewer today