Shop
Filters
Accessories
USB-C Female to USB-A Male Adapter
Tag-Connect Adapter, 10-way
20-way 0.1″ dual-row female to 10-way 0.1″ dual-row shrouded header.
Coresight 20 Adapter
20-way 0.1” connector to a standard Coresight 20 20-way 1.27 mm connector.
Coresight 10 Adapter
20-way 0.1” connector to a standard Coresight 10 10-way 1.27 mm connector.
XJLink-PF20 Mounting Kit
Brackets and fixing kit suitable for mounting XJLink-PF20 test controllers.
XJLink-PF40 Mounting Kit
Brackets and fixing kit suitable for mounting XJLink-PF40 test controllers.
2x 10-way 0.1” Adapter
Splits signals across 2x 10-way 0.1” connectors allowing two 10-way cables to be plugged in.
2x 10-way 2 mm Adapter
Splits signals across 2x 10-way 2 mm connectors allowing two 10-way cables to be plugged in.
0.1” to 1.27 mm Adapter
Converts pitch to a 20-way 1.27 mm header which you can connect a 20-way cable onto.
0.1” to 2 mm Adapter
Converts pitch to a 20-way 2 mm connector allowing a 2 mm cable to be plugged in.
Xilinx Adapter
20-way 0.1” connector to a standard Xilinx 14-way 2 mm connector.
Splitter / Signal Integrity Board, Standard
Splits signals from a 20-way 0.1” cable onto 2 other 20-way cables. ‘Hard grounds’ between active signals improve signal integrity.
Splitter / Signal Integrity Board, PXI
Splits signals from a 20-way MDR connector into two 20-way 0.1” connectors. ‘Hard grounds’ between active signals. Fits PXI-XJLink2.
Splitter / Signal Integrity Board SFF
Splits signals from a 20-way 0.1” into two 20-way 0.1” connectors. ‘Hard grounds’ between active signals. Small Form Factor. Fits XJQuad.
Splitter / Signal Integrity Board, Elbow
Splits signals from a 20-way 0.1” into two 20-way 0.1” connectors. ‘Hard grounds’ between active signals improve signal integrity.
Signal Breakout Board
Inserts inline in a 20-way ribbon cable between test controller and UUT.
Termination and Protection Board
Provides series termination to signals to/from a test controller to improve speed, reliability and transient protection.
ICT Relay Board
Allows TAP signal connections on the UUT to be switched between a test controller and other test/programming equipment.
XJTAG Surge Protection Board
Provides safeguards against excessive inrush current, over-current and overvoltage for the Unit Under Test.
XJXDP Adapter
Powered adapter for connecting a test controller to an Intel® XDP debug header.
XJIsolator
Provides galvanic isolation between a test controller and a UUT. Can be easily mounted inside a test fixture.
XJExtender
XJTAG’s recommended LVDS adapter to overcome signal integrity issues when connecting a test controller to a UUT up to 10 m away.
XJAccelerator SODIMM
Multipurpose FPGA module in SODIMM form factor to accelerate programming functions and extend test coverage as part of a test fixture.
XJAccelerator v2 Active Protector
Additional optional protection for the XJAccelerator v2 board against potentially damaging voltages.
XJAccelerator v2
Multipurpose FPGA unit that integrates with your XJTAG system to facilitate and accelerate programming functions and extend test coverage on a UUT.
XJComms Card
XJIO Board add-on for testing common automotive interface signals (CAN, RS-485/RS-422, FlexRay, LIN).
XJIO Board
Expansion unit to improve the test coverage of your UUT. 208 I/O, 8 A/D, 8 D/A, buttons, LEDs.