What JTAG Actually Enables

Simon Payne, CEO, XJTAG | Subscribe to LinkedIn newsletter

Last week, we explored why JTAG was created.

As electronic systems became more complex, traditional methods of accessing and testing hardware became increasingly difficult. Semiconductor manufacturers needed a standardised way to interact with devices once they were mounted on densely populated PCBs.

That solution became JTAG.

But understanding why JTAG exists only tells part of the story.

The more interesting question is: What does JTAG actually enable?

More Than a Connector

For many engineers, JTAG is associated with a connector on a PCB.

Others know it primarily as a method of programming devices.

While both are true, they only scratch the surface.

At its core, JTAG provides something much more valuable:

Access.

The ability to communicate with devices that would otherwise be difficult or sometimes impossible to reach.

Access to the Device

One of the most common uses of JTAG is device access.

Through a small number of pins, engineers can:

Identify devices
Read device information
Verify communication
Check device status
Interact with internal registers

This capability alone can significantly simplify bring-up and debug activities.

Before any software, firmware or application functionality is considered, engineers can establish whether the device itself is alive and responding.

Programming Devices

JTAG is widely used to program devices after assembly.

This includes:

FPGAs
CPLDs
Configuration memories
Flash devices
Microcontrollers
Processors

Rather than removing devices for programming or relying on specialised production fixtures, engineers can program devices directly on the assembled PCB. This simplifies both development and manufacturing.

Testing Connections

Perhaps one of the most powerful capabilities enabled by JTAG is boundary scan testing.

Boundary scan allows signals to be driven and observed through the boundary scan logic embedded within semiconductor devices. This makes it possible to verify PCB connectivity even when signals are physically inaccessible.

Engineers can use this capability to:

Detect open circuits
Detect shorts
Verify assembly quality
Validate connectivity

This is particularly valuable for BGAs and densely routed designs where traditional probing methods are limited.

More Than Testing JTAG Devices

One common misconception is that JTAG testing is limited to connections between JTAG devices.

In reality, JTAG-enabled devices can often provide access to much larger portions of the board.

Once signals can be driven and observed through the boundary scan infrastructure, engineers can use those signals to interact with many non-JTAG devices connected to the circuit.

Depending on the design, this may include:

Memories
I²C devices
SPI peripherals
Clocking circuits
Analogue interfaces
Power management devices

This ability to extend visibility beyond the JTAG chain itself is one of the reasons boundary scan has become such a valuable technology for board bring-up, debug, and production test.

Debugging Hardware

When a board does not behave as expected, one of the first questions engineers ask is:

“Is the hardware correct?”

JTAG provides a structured way to answer that question.

Engineers can:

Verify device access
Check signal states
Investigate connectivity
Confirm configuration paths

Rather than relying entirely on functional behaviour, they can establish confidence in the hardware itself.

Supporting Manufacturing

As systems move from development into production, JTAG often takes on an additional role.

It can be used to:

Program devices
Test assemblies
Verify manufacturing quality
Support fault diagnosis
Improve production coverage

Importantly, many of these activities can be automated and repeated consistently across large numbers of boards.

A Technology That Quietly Sits Everywhere

One of the reasons JTAG is so widely adopted is that it supports the entire product lifecycle.

The same interface may be used for:

Development
Bring-up
Debug
Production test
Repair
Field support

Few technologies remain useful across so many stages of a product’s life.

Yet most engineers interact with JTAG every day without necessarily thinking about how much capability it provides.

Why It Matters

As electronic systems continue to increase in complexity, visibility becomes increasingly important.

The ability to:

Access devices
Understand hardware behaviour
Verify connectivity
Program systems
Diagnose faults

all starts with having a reliable mechanism for interacting with the hardware.

That is what JTAG enables.

Not just programming.

Not just testing.

But access, visibility, and confidence in increasingly complex electronic systems.

Closing Thought

JTAG was originally developed to solve a manufacturing challenge.

Over time, it evolved into something much broader.

Today it provides one of the most important foundations for bringing up, testing, programming, debugging and supporting electronic systems.

And in many cases, engineers rely on it long before they realise how much it is doing behind the scenes.

JTAG Tip of the Week

Think about the entire product lifecycle when designing your JTAG interface.

The same JTAG connection may be used by:

Development engineers
Test engineers
Manufacturing operators
Service technicians

Designing for easy access, clear documentation, and long-term usability can deliver benefits far beyond initial bring-up.

Good JTAG design isn’t just about development.

It’s about supporting the board throughout its entire life.

Explore your board design with the free XJTAG Layout Viewer

To get started find out how the free XJTAG Layout Viewer can help you see your board connections:

Download your Free XJTAG Layout Viewer today

Find the fault. Save the board.

Start free trial

“It’s Only a Small Board Change…” What Could Possibly Go Wrong? We recently spoke to an engineer about a new revision of an existing PCB. The message was: “It’s only an iterative change.” The implication was understandable: the design changes are small, so the additional test work should also be small. And they may be absolutely right. But it raises an important question: How do you know? A small PCB revision does not automatically mean a small test impact. How Much Test Work Does a Small PCB Revision Really Create? The answer depends less on how many things changed and more on what those changes affect. A reset signal may have moved. A buffer may have been added. A memory device may have been replaced. A previously unused FPGA pin may now be connected. A power rail or enable sequence may have changed. Each change may be small on the schematic, but if an existing test depends on it, the impact can be much greater. Every test makes assumptions about the hardware: which devices are fitted, how signals are connected, what can be controlled and observed, and how devices behave during test. Change one of those assumptions and the existing test may need to change too. What If the Change Is at the Centre of the Board? Now consider replacing the FPGA or processor at the heart of the design. Perhaps the new device performs essentially the same function and most of the surrounding circuitry is unchanged. It may look like a straightforward substitution. But that device may interact with a significant proportion of the board and therefore affect many existing tests. For teams using Boundary Scan, there is another important consideration: Is the BSDL file correct for the exact device and package now fitted? Boundary Scan software relies on the BSDL file to describe the device's pins, Boundary Scan cells, instructions and test capability. So a change that appears on the design change list as: “FPGA changed from A to B” could potentially affect considerably more of the existing test strategy than the change list initially suggests. This is why test effort isn't proportional to the number of changes. It depends on how central those changes are to the tests already developed. Regression Testing Isn't Just for Software Software engineers are familiar with regression testing. A small code change doesn't mean rewriting the entire application, but it does mean understanding what else could have been affected. PCB test deserves the same approach. For every revision, ask: What changed? Which existing tests depend on it? Which assumptions are still valid? Which tests can remain unchanged? Which tests need modifying? Is any additional test coverage required? The objective isn't to assume everything has changed. It's to avoid assuming nothing has. Reuse Should Still Be the Goal Last week, we looked at the value of reusing tests developed during bring-up through production, repair and support. A new board revision shouldn't change that principle. Good reusable tests should make iterative development easier. The aim is to preserve everything that remains valid and concentrate engineering effort only on the tests affected by the new design. Reuse the test — but validate the assumptions behind it. That is far more efficient than designing a complete test strategy again for every PCB revision. Closing Thought “It’s only an iterative change” may be completely true. And the additional test-development work may genuinely be trivial. But that should be the conclusion of an impact review, not the assumption at the start of one. When the next PCB revision is released, ask: What changed? Which of our existing tests depend on those changes? Are the assumptions behind those tests still valid? Then preserve everything that still works. The objective isn't to design a complete test from scratch. It's to know which tests need changing — and why. Board Design Tip of the Week When documenting your next PCB revision, add one more item to the change list: Test impact. For each design change, consider whether it affects: Component functionality or pinout Signal routing or connectivity Resets, enables or mode settings Power rails or sequencing Interfaces and control signals Physical test access Programming or configuration Existing test assumptions And if Boundary Scan forms part of your test strategy, also check whether the change affects the BSDL/device model or JTAG architecture. A short review at this stage can prevent a “small change” from becoming an unexpected test-development problem when the revised boards arrive. Discover more about your board design with the Free XJTAG Layout Viewer. To get started find out how the Free XJTAG Layout Viewer can help you see on your board: Download your Free XJTAG Layout Viewer today

Don’t Throw Away the Tests That Got Your Prototype Working The first prototype arrives and the engineering team begins the process of proving the hardware. Connections are checked. Memories are exercised. Peripherals are tested. Problems are found, understood and fixed. Eventually, the board works. And then something slightly strange can happen. Much of the test capability that helped get it working is never used again. Bring-Up Creates More Than a Working Board During bring-up, engineers build up a significant amount of knowledge about the hardware. They learn how to initialise devices. They discover which signals need to be controlled. They find ways of checking memories and peripherals. They work out how to distinguish between a software problem and a hardware problem. Sometimes this knowledge becomes a formal test. Sometimes it is a small utility written by one engineer. Sometimes it is little more than a sequence of commands, measurements or notes that helped prove a particular part of the board. But whatever form it takes, it has value. The question is: What happens to it once the prototype works? A Test Shouldn't Necessarily Be Used Only Once Some bring-up tests are naturally temporary. But many aren't. If a test helped prove that an interface was correctly connected on the first prototype, there may be no reason why the same test cannot help verify that interface again later. The purpose simply changes. During bring-up, the question might be: “Did we design this correctly?” During production: “Has this particular board been assembled correctly?” During repair: “Which part of this board is no longer behaving correctly?” Different stages of the product lifecycle. But often the same underlying hardware evidence is useful. Turn Engineering Knowledge into Something Repeatable There is an important difference between knowing how to test something and having a test that someone else can run. If an engineer manually performs a sequence of checks during bring-up, that knowledge may disappear when the project moves on. If the same procedure is documented and automated where practical, it becomes reusable. That means the effort invested during development can continue providing value. Instead of every new team starting again, the product carries some of its diagnostic knowledge with it. Boundary Scan Is Particularly Well Suited to Reuse Boundary Scan can be especially useful here because structural tests are based on the hardware and its connectivity rather than depending entirely on the final application software. A test created to verify connections between devices during bring-up can potentially verify those same connections during manufacturing. A test used to exercise a memory, peripheral or other accessible device may remain useful during fault diagnosis. The reason for running the test changes. The physical hardware being checked does not. That gives structural tests the potential to move with the product from development into production and later support. Don't Lose the Tests at Handover When a product moves from development into manufacturing, the handover typically includes things such as: Schematics PCB data BOMs Manufacturing information Firmware Programming files Test specifications It is worth asking whether the diagnostic capability developed during bring-up should be treated in exactly the same way. Which tests proved particularly useful? Which interfaces can be independently verified? Which procedures helped isolate previous faults? Which tools or scripts should be retained? If that knowledge stays with one engineer rather than moving with the product, its value can easily be lost. One Investment, Several Uses The same test capability can potentially support: Prototype bring-up — establishing confidence in the first hardware. Design verification — proving that important areas of the PCB behave as intended. Production — checking whether individual assemblies have been manufactured correctly. Repair and rework — confirming whether a fault has been successfully corrected. Failure analysis — narrowing down where to investigate a returned board. Long-term support — providing engineers with diagnostic capability years after the original development team has moved on. That starts to change the way we think about the cost of developing a test. It isn't necessarily an investment for one stage of the project. It can be an investment in the product's entire lifecycle. Where XJTAG Fits This is one reason an XJTAG project can become more than something used to bring up the first prototype. Once the design information, device models and tests have been developed, that work can potentially be reused as the product moves into manufacturing, repair and support. Rather than rebuilding the test strategy at every stage, the same underlying project can evolve with the hardware. The value isn't simply in running another test. It is in preserving and reusing what the engineering team has already learned. Closing Thought Getting the first prototype working shouldn't necessarily be the point at which your test investment ends. It can be the point at which that investment starts becoming reusable. The tests that help an engineer understand board number one may also help manufacturing verify board number 1,000—or help a service engineer understand a failure years later. A good test isn't just something you run. It's engineering knowledge you can reuse. Board Design Tip of the Week When your next prototype reaches the point where everyone agrees it is working, don't immediately move on. Ask: “Which of the tests and diagnostic procedures we've developed should follow this product into production and support?” Capture them. Document them. Automate them where practical. And consider keeping them under the same configuration control as the rest of the product. The knowledge required to prove the first board works may be just as valuable when a board much later in the product's lifecycle doesn't. Discover more about your board design with the Free XJTAG Layout Viewer. To get started find out how the Free XJTAG Layout Viewer can help you see on your board: Download your Free XJTAG Layout Viewer today

Your Board Already Has a Powerful PCB Test Capability The design has been verified, production starts, the first boards come through test successfully. Then one fails. That is the moment you discover how good your test strategy really is. Finding a fault on a prototype is one thing. The development team knows the design intimately, has access to schematics, debug software and bench equipment, and may be prepared to spend hours investigating an unusual problem. Production is different. When a manufactured board fails, the question isn't simply: “Does it work?” It becomes: “What's wrong with this particular board, and how quickly can we find the fault?” Prototype Debugging and Production Diagnosis Are Different During development, engineers are often investigating the design itself. Is the interface configured correctly? Does the circuit behave as expected? Are the component values right? Does the software initialise the hardware correctly? By the time a product reaches production, the design should already have been proven. The production test is answering a different question: Has this particular assembly been manufactured correctly? That changes the nature of the investigation. A Failure Needs to Narrow the Search Imagine a board fails because an interface is not responding. A basic production test may tell you exactly that: Interface failed. But the engineer still has to work out why. Is there an open connection? A short? A missing component? A badly soldered pin beneath a BGA? An incorrectly fitted device? Or is the problem somewhere else entirely? A useful test strategy should progressively reduce that search area. The closer the test can get from: “Something is wrong.” to: “Start looking here.” the more useful it becomes. This Is Where Structural Information Helps Functional testing is extremely valuable in production because it proves that the completed product behaves as expected. But when a functional test fails, the symptom can sometimes cover a large area of hardware. Structural testing provides a different layer of evidence. Boundary Scan can often verify inaccessible PCB connections independently of the application software and relate unexpected results back to the nets and devices involved. That can help answer an important question: Is this an assembly problem, and if so, where should we investigate first? Boundary Scan does not replace functional production testing. It complements it by providing another way to understand the hardware beneath the symptom. One Failed Board May Be Manageable If one board fails, spending an hour investigating it may not seem significant. But what happens when ten fail? Or fifty? Or when the same type of fault appears repeatedly? At that point, diagnostic time starts affecting manufacturing throughput. That is why the economics of production test aren't determined only by how quickly passing boards can be tested. They are also influenced by how efficiently failed boards can be diagnosed. A fast PASS/FAIL test followed by hours of fault finding may not be as efficient as it first appears. Don't Wait for the First Failure to Think About Diagnosis There is an important Design for Test lesson here. When the first failed production board arrives, the PCB design is already complete. If a reset cannot be controlled, an enable is inaccessible or an important interface cannot be exercised independently, the test engineer has to work within those constraints. The opportunity to make a simple schematic change may have disappeared months earlier. This is why testability shouldn't only ask: “Can we detect a failure?” It should also ask: “If it fails, what information will we have?” That question is much easier to answer while the schematic is still open. Carry What You Learned During Bring-Up into Production There is another opportunity that is often overlooked. Structural tests developed during prototype bring-up don't necessarily need to be discarded once the design is working. Tests that proved connectivity, memories, peripherals or interfaces during development may also provide useful coverage in production. That means the effort invested in understanding the first prototypes can potentially become part of the manufacturing test strategy. Instead of starting again, knowledge moves forward with the product. Closing Thought A string of passing boards doesn't really test your diagnostic strategy. The first failure does. That is when you discover whether your test simply detects a problem or actually helps the engineer understand it. And the difference between knowing: “This board failed.” and: “This is where you should start looking.” can determine whether the problem is diagnosed in minutes, investigated for hours or placed on a growing bone pile marked: Investigate later. The best production tests don't just catch faults. They help engineers understand them. Board Design Tip of the Week Before releasing your next design, choose three realistic manufacturing faults. For example: An open connection beneath a BGA A short between two adjacent signals An incorrectly fitted peripheral Then ask: “If this happened on the production line, what would our test actually tell us?” If the answer is simply: FAIL there may still be work to do. Discover more about your board design with the Free XJTAG Layout Viewer. To get started find out how the Free XJTAG Layout Viewer can help you see on your board: Download your Free XJTAG Layout Viewer today