Shop
Filters
All products
XJDeveloper
Full IDE for rapid test and in-system programming development and debug. Test coverage analysis, XJRunner app and extensive library of non-JTAG device models included.
XJRunner
Production test tool for high or low volumes with power diagnostics built in. Test and/or program with fast fault location and visualisation.
XJAnalyser with XJLink2
Standalone visual analysis/debug tool with XJLink2 controller. Control JTAG device pins directly or program using SVF/STAPL files.
XJExpress-FPGA
Standalone Ultra-Fast FPGA-Accelerated Flash Programmer
XJExpress
Standalone Fast SPI Flash Programmer for Development & Manufacture
XJLink-PF20
USB JTAG test controller with 4 TAPs to 1 UUT, 20 I/O pins, configurable TAP frequencies, 2 voltage banks.
XJLink-PF40
USB JTAG test controller with 8 TAPs to 1 UUT, 40 I/O pins, configurable TAP frequencies, 4 voltage banks.
XJQuad
4-port USB JTAG test controller enabling simultaneous testing of up to 4 UUTs, each with 4 TAPs. XJLink2 compatible.
XJLink2
USB JTAG test controller with 4 TAPs to 1 UUT, 18 I/O pins, configurable JTAG port, 2 voltage banks.
PXI-XJLink2
JTAG test controller for PXI-based systems, integrating with LabVIEW, LabWindows, TestStand, or custom .NET applications. XJLink2 compatible.
XJLink2-3070
JTAG test controller for Keysight (Agilent) i3070 in-circuit tester integration. XJLink2 compatible.
XJLink2-3030
JTAG test controller for SPEA 3030 in-circuit tester integration. XJLink2 compatible.
20-way IDC breakout cable 200mm (0.1″)
20-way 0.1” IDC connector breaks out into 10 twisted pairs. 200 mm length.
USB cable 2m C-C
Coresight 20 Adapter
20-way 0.1” connector to a standard Coresight 20 20-way 1.27 mm connector.
Coresight 10 Adapter
20-way 0.1” connector to a standard Coresight 10 10-way 1.27 mm connector.
XJLink-PF20 Mounting Kit
Brackets and fixing kit suitable for mounting XJLink-PF20 test controllers.
XJLink-PF40 Mounting Kit
Brackets and fixing kit suitable for mounting XJLink-PF40 test controllers.
USB cable 1m C-C
USB cable 1m C-C locking
Blue USB cable 1.8m A-B
20-way straight ribbon cable 200mm (0.1″)
20-way twisted ribbon cable 220mm (0.1″)
20-way twisted ribbon cable 1000mm (0.1″)
2x 10-way 0.1” Adapter
Splits signals across 2x 10-way 0.1” connectors allowing two 10-way cables to be plugged in.
2x 10-way 2 mm Adapter
Splits signals across 2x 10-way 2 mm connectors allowing two 10-way cables to be plugged in.
0.1” to 1.27 mm Adapter
Converts pitch to a 20-way 1.27 mm header which you can connect a 20-way cable onto.
0.1” to 2 mm Adapter
Converts pitch to a 20-way 2 mm connector allowing a 2 mm cable to be plugged in.
Xilinx Adapter
20-way 0.1” connector to a standard Xilinx 14-way 2 mm connector.
Splitter / Signal Integrity Board, Standard
Splits signals from a 20-way 0.1” cable onto 2 other 20-way cables. ‘Hard grounds’ between active signals improve signal integrity.
Splitter / Signal Integrity Board, PXI
Splits signals from a 20-way MDR connector into two 20-way 0.1” connectors. ‘Hard grounds’ between active signals. Fits PXI-XJLink2.
Splitter / Signal Integrity Board SFF
Splits signals from a 20-way 0.1” into two 20-way 0.1” connectors. ‘Hard grounds’ between active signals. Small Form Factor. Fits XJQuad.
Splitter / Signal Integrity Board, Elbow
Splits signals from a 20-way 0.1” into two 20-way 0.1” connectors. ‘Hard grounds’ between active signals improve signal integrity.
Signal Breakout Board
Inserts inline in a 20-way ribbon cable between test controller and UUT.
Termination and Protection Board
Provides series termination to signals to/from a test controller to improve speed, reliability and transient protection.
ICT Relay Board
Allows TAP signal connections on the UUT to be switched between a test controller and other test/programming equipment.
XJTAG Surge Protection Board
Provides safeguards against excessive inrush current, over-current and overvoltage for the Unit Under Test.
XJXDP Adapter
Powered adapter for connecting a test controller to an Intel® XDP debug header.
XJIsolator
Provides galvanic isolation between a test controller and a UUT. Can be easily mounted inside a test fixture.
XJExtender
XJTAG’s recommended LVDS adapter to overcome signal integrity issues when connecting a test controller to a UUT up to 10 m away.
XJAccelerator SODIMM
Multipurpose FPGA module in SODIMM form factor to accelerate programming functions and extend test coverage as part of a test fixture.
XJAccelerator v2 Active Protector
Additional optional protection for the XJAccelerator v2 board against potentially damaging voltages.
XJAccelerator v2
Multipurpose FPGA unit that integrates with your XJTAG system to facilitate and accelerate programming functions and extend test coverage on a UUT.
XJComms Card
XJIO Board add-on for testing common automotive interface signals (CAN, RS-485/RS-422, FlexRay, LIN).
XJIO Board
Expansion unit to improve the test coverage of your UUT. 208 I/O, 8 A/D, 8 D/A, buttons, LEDs.
XJTAG DFT Assistant for Mentor Xpedition and PADS
XJTAG DFT Assistant for Zuken CR-8000
